Plumbing fixture
A plumbing fixture is an exchangeable device which can be connected to an existing plumbing system to deliver and drain away water but which is also configured to enable a particular use.
Contents |
[edit] Common fixtures
The most common plumbing fixtures are:
- Bathtubs
- Bidets
- Channel drains (also called trench drains)
- Drinking fountains
- Hose bibbs (connections for water hoses)
- Kitchen sinks
- Lavatories (also called bathroom sinks)
- Showers
- Tapware - an industry term for that sub-category of plumbing fixtures consisting of tap valves, also called water taps (British English) or faucets (American English), and their accessories, such as water spouts and shower heads.
- Terminal valves for dishwashers, ice makers, humidifiers, etc.
- Urinals
- Utility sinks
- Water closets (WC) (known as toilets in the USA, loos, flush toilets or lavatories in Britain)
[edit] Outlets and drains
Each of these plumbing fixtures has one or more water outlets and a drain. In some cases, the drain has a device that can be manipulated to block the drain to fill the basin of the fixture. Each fixture also has a flood rim, or level at which water will begin to overflow. Most fixtures also have an overflow, which is a conduit for water to drain away, when the regular drain is plugged, before the water actually overflows at the flood rim level. However, water closets and showers (that are not in bathtubs) usually lack this feature because their drains normally cannot be stopped.
Each fixture usually has a characteristic means of connection. Normal plumbing practice is to install a valve on each water supply line before the fixture, and this is most commonly termed a stop or "service valve". The water supply to some fixtures is cold water only (such as water closets and urinals). Most fixtures also have a hot water supply. In some occasional cases, a sink may have both a potable (drinkable) and a non-potable water supply.
Lavatories and water closets normally connect to the water supply by means of a supply, which is a tube, usually of nominal 3/8 in (U.S.) or 10 or 12 mm diameter (Europe and Middle East), which connects the water supply to the fixture, sometimes through a flexible (braided) hose. For water closets, this tube usually ends in a flat neoprene washer that tightens against the connection, while for lavatories, the supply usually ends in a conical neoprene washer. Kitchen sinks, tubs and showers usually have supply tubes built onto their valves which then are soldered or 'fast joint'ed directly onto the water supply pipes.
[edit] Traps and vents
All plumbing fixtures have traps in their drains; these traps are either internal or external to the fixtures. Traps are pipes which curve down then back up; they 'trap' a small amount of water to create a water seal between the ambient air space and the inside of the drain system. This prevents sewer gas from entering buildings.
Most water closets, bidets, and many urinals have the trap integral with the fixture itself. The visible water surface in a toilet is the top of the trap's water seal.
Each fixture drain, with exceptions, must be vented so that negative air pressure in the drain cannot siphon the trap dry, to prevent positive air pressure in the sewer from forcing gases past the water seal, and to prevent explosive sewer gas buildup.
[edit] Drains
The actual initial drain part in a lavatory or sink is termed a strainer. If there is a removable strainer device that fits into the fixed strainer, it is termed a strainer basket. The initial pipe that leads from the strainer to the trap is termed the tailpiece.
Floor-mounted water closets seal to the toilet flange of the drain pipe by means of a wax ring. These are traditionally made out of beeswax. However, their proper sealing depends on proper seating of the water closet, on a firm and secure base (floor), and on proper installation of the closet bolts which secure the closet to the flange, which is in turn supposed to be securely fastened to the floor.
[edit] Electronic plumbing
In public facilities, the trend is toward sensor-operated fixtures that improve hygiene and save money. For example, sensor operated automatic-flush urinals have fewer moving parts, reduce wear, and tend to last longer than manual-flush valves. Also they ensure fixtures are flushed only once per use. Some contain intelligence that flushes them at different amounts of water flow depending on traffic patterns: e.g., the fixture can detect a lineup of users and only give a full flush after the last person has used the urinal.
Automatic flush compensates for users who do not bother to flush. Also, since
the fixtures are always flushed, there is no need for a urinal
cake, or other odor reduction. Sensor-operated toilets also have automatic
flush. Sensor-operated faucets and showers save water. For example, while a user
is lathering up with soap, the fixture shuts off and then resumes when the user
needs it to. Sensor-operated soap and shampoo dispensers reduce waste and spills
that might otherwise represent a slippage hazard.
However, many people, especially children, dislike or even fear automatic flush toilets, since they have the tendency to flush without warning, even while the user is still sitting on the toilet. Some parents have started keeping track of public bathrooms that have manual flush toilets, or even carrying post-it notes or other devices with them to temporarily disable the automatic flush sensor.[1]
These fixtures typically cost more to install than conventional plumbing fixtures, because thy require the services (or presence) of both a licensed plumber and a licensed electrician. Construction companies on cost-plus contracts may actually favor these fixtures for this reason, although their clients may not. The additional complexity of these fixtures also complicates repairs, particularly the diagnosis of malfunctions causing unexpected flushing. Few electricians, and fewer plumbers, understand microelectronics well enough for complex diagnosis.
[edit] Garbage disposer
The garbage disposer (UK: waste disposal unit, Canada: garbage grinder or garburator, portions of US: garbage disposal) was invented in 1927 by architect John Hammes of Racine, WI. He went on to found InSinkErator, which is still at work making millions of garbage disposers a year. The function of the garbage disposer is to grind food waste (e.g. chicken bones, fruit, coffee grinds, meat) so that it can be sent down standard household plumbing without clogging. The device works by attaching a small chamber underneath the drain of a sink. This chamber contains whirling blades and grinders which chop and grind the waste into much smaller particles. Once the food is small enough to pass out of this chamber, it is flushed down the rest of the plumbing.
In most of Europe, garbage disposers are not used at all; the high load of organic matter in the waste water requires a higher capacity sewage treatment plant, since the increased organic matter requires additional oxygen and water to process. Instead, garbage is separated at the source, into compostable and other types of garbage and collected. Similarly, in the United States there have been some political and environmental issues with garbage disposers. For many years, New York City had banned their use. The stated reason was the above-mentioned increased sewage treatment capacity, but many area residents also suspected that it was the garbage unions not wanting work taken away from them. The ban was rescinded on September 11, 1997.[2]
